🏠 ATE LC30 Black – Electromagnetic device for damp walls
Wall drying – An electromagnetic solution against rising damp
Wall dampness is a common problem, often caused by rising damp. Water present in the ground naturally moves upward through the building’s porous materials such as brick, stone, or plaster. This phenomenon weakens the structure, reduces thermal comfort, and encourages mold growth.
The ATE LC30 Black is an electromagnetic anti-damp device designed to dry walls without injecting chemical products. Thanks to its wall drying technology, it acts directly at the source of the problem.
Model documentation · ATE LC30
English version · PDF
For contractors and resellers
Video in English
⚙️ How does the ATE LC30 work?
Each wall generates a natural electrical potential that draws moisture upward. The device emits low-frequency electromagnetic pulses that reverse the polarity of these fields. Water molecules are therefore redirected downward, naturally returning to the foundations.
This process is continuous, silent, autonomous, and requires no maintenance.
✅ Benefits of the ATE LC30 Black
Coverage radius: 15 meters (30 m diameter)
No vibration, no noise, no harmful emissions
Very low power consumption: only 0.75 W (~€15/year)
Elegant, discreet black design
Manufacturer’s warranty: 10 years
Made in France
Certified to European standards (EMF, RoHS, EMC…)
📦 Technical specifications
Dimensions: 322 x 232 x 32 mm
Power supply: 12 V
Power consumption: 0.75 W
Maximum coverage: 30 m diameter
Installation: mounting on a load-bearing wall only
Certifications:
-
Low Voltage Directive 2014/35/EU
-
EMC Directive 2014/30/EU
-
RoHS Directive 2011/65/EU
-
WEEE Directive 2012/19/EU
-
EMF tested – non-harmful waves (Emitech laboratory)
🎯 Effectiveness and results
When the device is installed correctly and used according to the recommendations, significant drying results are generally observed within 18 to 24 months, depending on the building’s structure, the condition of the walls, and compliance with the guidelines.
🛠️ Installation tips
Height: 30 cm to 1 m above the floor, on a load-bearing wall or internal supporting wall (preferably damp)
Distance: at least 1.50 m from other electronic devices
Mounting: hang like a picture and avoid moving it after installation
Power: must remain plugged in continuously (very low consumption)
💡 Tips to optimize drying
Remove waterproof coverings 10–20 cm above the affected areas
Ensure good ventilation: install a ventilation system or adjust door undercuts/airflow paths
After drying, brush off surface salts, then redo renders with a lime-based mortar and anti-salt additive
Plan drainage if lateral water ingress is present (hydrostatic pressure)
⚠️ Important information
This device does not treat:
-
Active water ingress (roof leaks, flooding)
-
Mold already present on the walls
➡️ These issues must be addressed separately to ensure long-term effectiveness.
Frequently asked questions about ATE LC30
What type of damp is ATE LC30 intended for?
ATE LC30 is an electromagnetic device offered for walls affected by identified rising damp. It does not replace repairing a leak, addressing water ingress or resolving condensation.
What does the stated 30 m diameter mean?
The manufacturer states a coverage diameter of 30 m, equivalent to a 15 m radius around the device. This is not a floor area in square metres. Consider the distances to the affected walls and the layout of the building.
Does ATE LC30 need electricity?
Yes. ATE LC30 uses the power supply specified by the manufacturer and must remain powered as instructed in its manual.
How should I prepare to install ATE LC30?
Read the manual for ATE LC30 before installation. It explains the mounting surface, positioning and precautions. Use fixings suitable for the wall and follow the manufacturer’s instructions.
How does it differ from the other models?
ATE devices use mains power; ATG geomagnetic devices operate without electricity. Stated ATE coverage diameters are 15 m for LC15, 30 m for LC30 and LC30 PULSE, and 60 m for MAX. Compare the specifications and manual for each model.
Where can I find the ATE LC30 manual and specifications?
The English manual for ATE LC30 is linked below. Also check the product reference and finish on the shop page before ordering.
| Weight | 1.4 kg |
|---|




